SSUCT Series

Take up units available with SCO (open) or SCC (closed end) caps

#
QCB ref Dimensions
WhgObNqpaejkLBS
mminchmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmkg
SSUCT 20112 1/2946110165119325189763212213112.70.7
SSUCT 20215 5/8
SSUCT 20317 11/16
SSUCT 20420 3/4
SSUCT 205257/815/1619762101651193251897632122434.114.30.82
SSUCT 206301.3/161.1/411370111657223756101.58936.51227.538.115.91.23
SSUCT 207351.1/41.3/81.7/16130781416642237641028937123042.917.51.61
SSUCT 20840 1.1/21448817198329498311410249163349.2192.34
SSUCT 20945 1.5/81.3/4145.58718198329498311710249163549.2192.33
SSUCT 210501.7/81.15/162150.59018198629498311710249.5163751.6192.48
SSUCT 21155 22.1/8170106192595356410114513064223755.6223.79
SSUCT 21260 2.1/42.3/819311919.5321023564101.5144.513063224165.1254.61
Non stock sizes are available to order
#

SUC insert limiting speeds

The limiting speed of any ball bearing insert is, for practical purposes, determined by the quality of fit between the inner ring and the shaft.

QCB RefShaft tolerance
j7h7h8h9
SUC 2016700530038001400
SUC 2026700530038001400
SUC 2036700530038001400
SUC 2046000480034001200
SUC 2055600400030001000
SUC 206450034002400850
SUC 207400030002000750
SUC 208360026001900670
SUC 209320024001700600
SUC 210300022001600560
SUC 211260020001400500
SUC 212240018001200450

Setscrew tightening torque

The 2 setscrews should be tightened to the appropriate torque figure. Over tightening may result in a fracture developing in the inner ring.

Should the axial load be high, a small dimple in the shaft may improve the locking effect. For best effect the bearings should be mounted against a shoulder in the shaft.

SizeTorque (Nm)
M64
M88
M1015

Materials

QCB® Stainless Steel bearing units are made in high quality stainless steel for maximum corrosion resistance.

All pillow blocks and flange units have a solid base and smooth exterior surface restrict the growth of bacteria.

PartMaterial
bearing insertInner and outer ringsStainless steelAISI 440C
BallsAISI 440 C
Cage/retainerAISI 321
Flinger sealAISI 321
Set screwsSU 304
Rubber sealsNitrile rubber
HousingHousing bodyStainless steelAISI 440 C
Grease nippleAISI 304

Food Grade Lubricant

QCB® Stainless Steel SUC inserts are lubricated with KLUBER PARALIQ GA343 grease

ndm valueEnvironmental conditionsTemperatureRelubrication interval
< 40 000Clean-15 to +65 °C6 - 12 months
+65 to +100 °C2 - 6 months
< 70 000Clean-15 to +65 °C2 - 6 months
+65 to +100 °C1 month
AnyDirty / Water splashAny1 month

Operating temperature range

QCB® Stainless Steel inserts can operate in environments from -30 to + 120C

#
QCB Stainless Catalogue

(PDF) 945.49 KB

Associated Products


Do you have a special project?

Need some advice? We can help!


oemsales@nbcgroup.co.uk

01952 222300